Quilting

Bargello Table Runner III

Posted by

2

I’ve just finished piecing the bargello table runner top. The second pair of blocks went quite a bit faster than the original two because I was careful about pressing seams in the right directions so I would have no nesting problems as I assembled the blocks.

Bargello Table Runner Top – Finished

The unanticipated thing was pressing seams as I constructed the blocks – I discovered I had to press the seams in the opposite direction from the original two blocks so seams would nest when I went to attach the new ones.

Next I have to find a backing fabric. I’m going to do a pillow case finish without bindings to preserve the clean edge I have here.

Bargello Table Runner II

Posted by

0

Years ago I did some wool on canvas bargello embroidery creating seat covers for several chairs.

Bargello done with wool and canvas

Bargello is done by stitching across a set humber of canvas threads – in this case I’d guess 4 threads – with adjacent stitches stepping down two threads. Also there are different numbers of stitches at different points – three consecutive stitches over the same threads, two, two, one, one, one, one… It’s the changing number of repeat stitches at any level that creates the interesting curved lines characteristic of bargello work.

It’s similar with creating bargello using fabric. Set up a panel from coloured strips, cut new strips of different widths from the panel, sew these strips together systematically staggering the colours to set up a bargello pattern.

Beginning to Lay Out The Pattern

Here is my completed bargello block:

Bargello “block”

Here are two blocks sewn together to make a curved diamond.

Bargello Double Block

Yesterday when I created a test block I wasn’t quite careful enough with my cutting, and my 1/4″ seam allowances weren’t perfect, so the finished panel was just a bit slanted. Instead of doing the same block using my second set of strips, I started a new layout and this time I made sure my ruler didn’t slip while cutting the initial strips, that I matched up my edges precisely when sewing them together, was particularly careful when cutting the panel into different width strips and nested the seam joins when sewing those strips together. My two blocks turned out pretty much the same dimensions (and although the photo doesn’t demonstrate it, this panel is straight).

The other thing I did this time was to add a 10th very dark strip next to my contrast colour. I ran into difficulty nesting the joins yesterday and that was because I had used just 9 strips initially – taking care to press my seams in alternate directions – but when I added in the contrast strip and joined it to the first (creating a tube) I ended up with a pressed seam not paired to another and as a result I was changing nesting direction for just about each join/point while assembling the block. With 10 initial strips I had the right number of seams that when pressed in opposite directions matched up.

Seams pressed in opposite directions

Sewing the different width staggered strips together was nearly effortless – the nestings were all just about exact. So in spite of some directions I’d found online calling for an odd number of strips to form the bargello layout, it turns out an even number of initial differently coloured strips makes the later sewing much easier.

Charm Quilt Top II

Posted by

2

I spent a couple of days looking at the finished quilt top and decided it wasn’t finished after all – it needed something in the border below the panel to mirror the stripes in the left border.

Revised Quilt Top

So, I carefully unstitched the border below the panel, created two strips from scraps, inserted them into the border, trimmed the border (praying I was getting the size exact so it would fit back into the original space and lie flat).

It did.

The quilt top now has balance which it didn’t have before.

The quilt back is also done. I incorporated the column of HST I removed from the panel, added a border on the right, then two sets of pieced sashing on either side. I slit the backing fabric leaving 12″ to the right and inserted the strip.

Charm Quilt Back

The quilt sandwich is now pinned and ready to be quilted in the hoop. I extended the blocks into the borders by marking them using a Frixion pen (heat erasable). I’d planned the borders to equal multiples of the original 4.5″ quilt block so the quilting should work out relatively easily. That will get underway this weekend – I will do a few blocks to show how I do the quilting for my class on Wednesday.

Quilt Sandwich

Charm Quilt Top

Posted by

0

In the end I went with an on-point square layout set off-centre.

7 x 10 HST Panel

However, the finished panel was too small, even with 3.5″ borders, to be a good size throw quilt. So what to do with it…

I had used all of the white/grey background fabric I had, I had no batik charms left. I also thought the 8 x 10 array wasn’t rectangular enough, so I removed one of the columns – set it aside to use in the quilt back.

Next, I decided to use the panel offset to one corner and create narrow pieced stripes in the wide border to the left of the panel as an accent for the HST array.

Completed Quilt Top

To build out the quilt, I added 9″ of backing fabric (a different pale grey/white fabric which blended with the original fabric) to the bottom of the panel so I knew the length of the  side panel. Then I began building pieced strips from everything I could find in my stash which blended, or implied, burgundy – the focal colour of the batik charms. I offset the strips by varying amounts from either the top or the bottom of the side piece by inserting appropriate amounts of backing fabric into the piecing. I completed the wide side border with a wide strip cut from the length of backing fabric to avoid a large, obvious mitre across the middle of it.

Finally I added a 3.5″ mitred outer border.

Now I’m ready to construct the backing. I bought a darker grey/white printed fabric for backing. I have a 4.5″ strip of HST I removed from the panel. I haven’t measured the panel width but I’m guessing it’s close to 54″ wide. So my insert panel will need to be at least 12″ wide.

No idea yet how the back will shape up. That’s for tomorrow.

Another HST Quilt

Posted by

0

Two weeks ago at class one of the gals gave me a batik charm pack in exchange for the materials I’d given her. The batiks – five related colours – all felt “burgundy”. I thought they’d work with a light background. I decided to create unequal half-square triangles.

I raided my stash of larger fabric pieces and found a remnant of a white with grey fabric from the Zen Chic Fragile Collection.  I measured it carefully – thought I had enough for 40 5″ squares, plus sashing pieces; I started cutting. Turns out I was close, but I had to hunt through boxes of scraps hoping to find a wee bit more – luckily I found exactly enough to scrounge 8 more 4 1/2″ sashing pieces. That was it – there are no scraps of any kind left! This fabric collection, this colour in particular, were popular and are nowhere to be found. Trust me, I looked for hours online.

Stitching Unequal HST

To construct the unequal HST I marked the diagonal, then another parallel line 1/2″ to one side. I chain stitched the diagonals, cut the blocks apart, chain stitched the second line, cut them apart. Then cut between the two lines of stitching. After pressing the blocks open, I added a 1″ sashing to two sides of the smaller triangles.

I’ve interleaved larger and smaller triangles and this is the 8 x 10 array I currently have on my floor. Kinda interesting….

Current Layout On The Floor

I decided to see what other arrays are possible. I took a photo, then cut the paper into sections so I could try other arrangements:

Pinwheel Array

The pinwheel is off centre (centre is at position 4/3). While the centre should provide focus, it doesn’t seem to in this case – what’s there is too busy.

Next layout:

Chevrons

The chevrons work better – the white lines draw your eye in toward the offset centre. However, this layout requires two smaller triangles which I don’t have. I have two of the larger triangles but not a single scrap of fabric to convert them into smaller triangles – no fabric to construct sashing!

I’ll probably stick with the array I currently have on the floor – I need to leave it there for a day or so to make sure I’m happy with the colour distribution.

I didn’t say the reason I’m doing this quilt is so I can demonstrate for a class in early February how to “quilt-in-the-hoop“. I need both a quilt top and back to do this. Stitched, this array is going to be on the small side (but with no more burgundy batik squares and no more backing fabric to extend the size by a row/column or two, I will enlarge the panel with an inner sashing and a wide outer border so the finished size lands somewhere between 40″-45″ x ~55″- 60”.

I have a piece of complementary burgundy fabric large enough for sashing; and the other day I bought a metre of soft grey which should work for the border. I’m thinking a hidden binding from the main backing fabric might be in order because I don’t think I want to define the outer edge of the quilt with another strong colour.

First to assemble the blocks into a panel. I’ll work on that tomorrow.

Another possible layout:

Diamond

This one works – and I’d complete the diamond on the right in the border (including a narrow sashing all around up to, but not including, that point…).

Hmmmm.

[BTW – I’ve been doing these different layouts by cutting a paper printout of the layout currently on my floor and holding it together with tape – no need to spend time on the floor arranging and rearranging blocks! The reason for placing my layout on the floor – my cutting table is too narrow to hold the width of the panel and I don’t have a space where I can hang a flannel design wall. I suppose I could set up a flannel panel and use weights to hold it in place on the floor – that could help keep the blocks from sliding around – but I’d still have to be on my knees to work with it.]

Nine Shades Of Grey – Completed

Posted by

1

Finished this quilt a couple of days ago, now. Although a very simple quilt, I find it’s simplicity appealing and I’m happy with how it turned out. I particularly like how the two narrow borders frame the inner panel bringing out the darker greys and highlighting the golden colours in the batik fabrics.

Nine Shades Of Grey

I’m happy with the back as well. Finding a way to use the small half-square triangles along with the cornered blocks was satisfying.

NIne Shades Of Grey – Quilt Back

I elected to bind the quilt in the same fabric as the wide outer border so the binding would be relatively invisible. I also didn’t use a decorative stitch to apply the front of the binding – I just straight stitched it down – harder to do accurately than working with the decorative stitch which is more forgiving! But I didn’t want to introduce any distracting detail into the overall simplicity of the quilt.

Magic Squares Quilt IV – Finished

Posted by

0

I finished the quilt on Thursday – quilted the last four squares and the border, then added the binding and label.

Magic Squares IV – Quilt Top

Final Size: 51.5″ x 62.5″ – largish for a throw but useful to keep at the bottom of a bed to use when it’s cold.

The quilt back:

Magic Squares IV – Back

I had four blocks left over which I bordered and inserted into the backing fabric. I was pleased with how the backing echoes the dark teal feel of the quilt top and the inserted rectangle stands out nicely.

People ask “How long does it take to make a quilt like this?” It’s not an easy question to answer particularly since in this case I was working on another quilt, making a gazillion zippered bags and sewing other things.

I started this quilt somewhere around Nov 10 when I started sewing jelly roll strips together, cutting the panels into squares in preparation for the sewing retreat (Nov 14-17) where I assembled the “magic squares” blocks. I got to laying out the squares on Dec 2. On Dec 5, I created the top panel by adding the sashing. On Dec 6, I added the outer border. Sometime during the next several days (while I made more bags, finished knitting a pair of men’s socks, worked on and finished the second “fish” skinny quilt got some baking done), I created the quilt back. I began quilting it a week ago – the quilting took three days finished on Dec 25. Binding the quilt took a morning; I added the label that evening – Dec 26.

So you could say I worked on the quilt for 6-7 weeks, but the actual working time was much less – probably not more than 10-12 days.

And now I’m quilting “Nine Shades Of Grey” which is going quite quickly. My goal is to have this second quilt finished before Dec 31. I think I will make it.

Two Skinny Quilts – Finished

Posted by

3

School Of Fish #2

School Of Fish #2

Finished with a hidden binding and backing fabric. I like this one even more than the original. I think the ombre fabrics create a feeling of water and notice the single fish swimming against the school…. But that’s it for fish – I have no more in my bag of fusible scraps.

Skinny Quilt #4 – An Update

Skinny Quilt IV – Straightened

I wasn’t happy with this banner – it wasn’t quite square and it showed when the piece was hanging. Yesterday, I took it apart so I could straighten the sides and while I had the backing and binding off, I decided to remove the smallest blue circle – first, because it was the wrong colour – it didn’t really show up – and second, it was the eighth circle and an odd number is more pleasing. Now the yellow in the top large circle is now echoed in the small one and your eye moves between the two and is then drawn into the complexity of the fabric design of the other circles. A better balance.

Best of all, the banner is now square so it hangs straight and I can include it I the banner/skinny quilt collection.

Magic Squares Quilt IV – 3

Posted by

2

Top done! I finished the sashing early this afternoon and just this minute finished the border with mitres all done properly the first time! And you can see from the photo that I managed to get the sashing to intersect well – that’s tricky on a quilt like this because all of the block outer edges are on the bias and therefore stretchy. To make sure I’d come close on size I carefully cut all the sashing pieces the same length and then eased the quilt block edges into place. The quilt top is square.

Sashed And Bordered!

It’s too bad really that I can’t capture the vibrance of the batiks with my iPhone camera – the quilt top is a lot brighter than it looks here. I’m much happier with the final panel than I thought I’d be – the light sashing toned down the 4-strip block corners and the border ties the many colours together, making the panel overall less red/green and more turquoise.

Now I need to construct two quilt backs – one for this quilt (I have lots of leftover half-square triangles with which to work), and another for the grey/gold quilt (and I have leftover blocks there as well).

So marching along with both projects at the same time.

 

Magic Squares Quilt IV – 2

Posted by

0

I completed the panel sashing this afternoon. The light fabric tones down this “quilt of many colours” somewhat. Now I need to add a narrow border using the sashing fabric to frame the panel. (Here’s what it looks like without the sashing.)

Quilt Of Many Colours

Then a border – I found this batik fabric in my stash a couple of days ago – it wasn’t the fabric I was originally planning to use to frame this panel but I think a 2 1/2″ border of this dark teal might just bring the colour hodgepodge together – fingers crossed.

Possible Outer Border

I plan on looking again through my stash – there may yet be another largish piece of fabric that works with the panel although I don’t see any in my mind’s-eye. I may even take the panel shopping to see if there is a fabric that says “take me.”

Yesterday, I gave away my “Fish” banner to a friend. Last evening, I dug out my remaining fish and this afternoon, I found some ombre fabric that might work well with them to create another skinny quilt/banner. It’s a quick and easy project to fill in my wall art collection for this year’s showing in Parrsboro. I lost close to three months of sewing/quilting time this summer with my fractured wrist. I’m trying to catch up so I have enough new creations to show.

Fish II

And while I’m at it, I will have a go at another couple of these skinny quilts – however, not until the two throw quilts I’m working on are finished – I try to complete one piece at a time before starting something else – that way I don’t have unfinished projects sitting around. I don’t know how other quilters live with a closet full of UFOs – I need closure.

So I will get the Magic Squares Quilt IV top done in the next day or two, then set up backs for both the grey/gold and this quilt and get both of them quilted – I’m aiming for end of December.